Announcement

Collapse
No announcement yet.

Autelis Pool Control Plug-in - Beta Testing

Collapse
This is a sticky topic.
X
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

    #16
    Hi Spudd

    I have your plugin installed and working.

    If I would want to set up an immediate command ( or a script) to say (for example)
    raise pool temperature setting

    is there a way of doing that?

    I tried an immedicate command of " http://192.168.1.189:80set.cgi?name=poolsp&temp=up " but got the following in the log

    Action of Control a Device could not be carried out because its configuration is not complete.

    Thanks

    Comment


      #17
      Originally posted by zsima View Post
      Hi Spudd

      I have your plugin installed and working.

      If I would want to set up an immediate command ( or a script) to say (for example)
      raise pool temperature setting

      is there a way of doing that?

      I tried an immedicate command of " http://192.168.1.189:80set.cgi?name=poolsp&temp=up " but got the following in the log

      Action of Control a Device could not be carried out because its configuration is not complete.

      Thanks
      Why don't you use the "-" and "+" controls attached to the pool setpoint device.
      You can use them from an event using the "Control A device" action

      Comment


        #18
        Thanks for the quick reply.

        I didn't see the + or - at the bottom of the list. I thought it only takes a
        specific number.

        Works fine Thanks again

        Comment


          #19
          Autelis Pool Control and Setup

          Hello,

          I have just installed an Autelis Pool Control For Jandy/Zodiac PDA module. I have installed your plugin and configured as shown below:

          Autelis Settings
          Type: Jandy/Zodiac
          IP Address: 192.168.2.18
          Port: 80
          Password: *******
          General Settings
          Poll for status every: 1 minutes
          Log Level: Debug

          I see on the logs:
          Oct-27 7:29:40 PM Autelis DEBUG 1.0.2 1477614576
          Oct-27 7:29:40 PM Autelis INFO CMD SENT: http://192.168.2.18:80/status.xml?

          So, that means the connectivity is good.

          However, HomeSeer did not create my device. Any idea:
          Unknown Autelis Root

          Am I missing anything?

          Thanks,

          Marcus

          Comment


            #20
            Originally posted by mmagri View Post
            Hello,

            I have just installed an Autelis Pool Control For Jandy/Zodiac PDA module. I have installed your plugin and configured as shown below:

            Autelis Settings
            Type: Jandy/Zodiac
            IP Address: 192.168.2.18
            Port: 80
            Password: *******
            General Settings
            Poll for status every: 1 minutes
            Log Level: Debug

            I see on the logs:
            Oct-27 7:29:40 PM Autelis DEBUG 1.0.2 1477614576
            Oct-27 7:29:40 PM Autelis INFO CMD SENT: http://192.168.2.18:80/status.xml?

            So, that means the connectivity is good.

            However, HomeSeer did not create my device. Any idea:
            Unknown Autelis Root

            Am I missing anything?

            Thanks,

            Marcus
            can you restart the plugin and post all the debug logs you get

            also what do you get when you paste this url in a browser running on your HS3 server: http://192.168.2.18:80/status.xml

            Comment


              #21
              Autelis Pool Control and Setup (additional info)

              Here you go.

              Not so verbose ... Please let me know if you need anything else ...

              Trying it before I buy it.

              Thanks.

              Oct-28 7:29:32 AM Autelis DEBUG 1.0.2 1477657768

              Oct-28 7:29:32 AM Autelis INFO CMD SENT: http://192.168.2.18:80/status.xml?

              Oct-28 7:28:32 AM Plug-In Finished initializing plug-in Autelis

              Oct-28 7:28:32 AM Autelis DEBUG 1.0.2 1477657708

              Oct-28 7:28:32 AM Autelis INFO CMD SENT: http://192.168.2.18:80/status.xml?

              Oct-28 7:28:32 AM Autelis INFO Autelis version 3.0.0.8

              Oct-28 7:28:32 AM Info Plugin Autelis has connected. IP:127.0.0.1:61628

              Oct-28 7:28:32 AM Plug-In Interface Autelis is running as a trial, 30 days remaining.

              Oct-28 7:28:26 AM Plug-In Shutting down Plug-In: Autelis



              http://192.168.2.18/status.xml?

              <?xml version="1.0"?>

              -<response>


              -<system>

              <version>1.0.2</version>

              <time>1477657750</time>

              </system>

              </response>

              Comment


                #22
                Originally posted by mmagri View Post
                Here you go.

                Not so verbose ... Please let me know if you need anything else ...

                Trying it before I buy it.

                Thanks.

                Oct-28 7:29:32 AM Autelis DEBUG 1.0.2 1477657768

                Oct-28 7:29:32 AM Autelis INFO CMD SENT: http://192.168.2.18:80/status.xml?

                Oct-28 7:28:32 AM Plug-In Finished initializing plug-in Autelis

                Oct-28 7:28:32 AM Autelis DEBUG 1.0.2 1477657708

                Oct-28 7:28:32 AM Autelis INFO CMD SENT: http://192.168.2.18:80/status.xml?

                Oct-28 7:28:32 AM Autelis INFO Autelis version 3.0.0.8

                Oct-28 7:28:32 AM Info Plugin Autelis has connected. IP:127.0.0.1:61628

                Oct-28 7:28:32 AM Plug-In Interface Autelis is running as a trial, 30 days remaining.

                Oct-28 7:28:26 AM Plug-In Shutting down Plug-In: Autelis



                http://192.168.2.18/status.xml?

                <?xml version="1.0"?>

                -<response>


                -<system>

                <version>1.0.2</version>

                <time>1477657750</time>

                </system>

                </response>
                The problem is that the PDA system does not support the API, read this thread: http://board.homeseer.com/showthread.php?t=173677

                Comment


                  #23
                  Additional info

                  Logs
                  _________________________________

                  Oct-28 9:41:01 AM Autelis DEBUG 1.0.2 1477665658
                  Oct-28 9:41:01 AM Plug-In Finished initializing plug-in Autelis
                  Oct-28 9:41:01 AM Autelis INFO CMD SENT: http://192.168.2.18:80/status.xml?
                  Oct-28 9:41:01 AM Autelis INFO Autelis version 3.0.0.8
                  Oct-28 9:41:00 AM Info Plugin Autelis has connected. IP:127.0.0.1:54356
                  Oct-28 9:41:00 AM Plug-In Interface Autelis is running as a trial, 30 days remaining.
                  Oct-28 9:40:25 AM Info Plugin Autelis with instance: has disconnected
                  Oct-28 9:40:25 AM Plug-In Shutting down Plug-In: Autelis

                  --------
                  http://192.168.2.18/status.xml?
                  <?xml version="1.0"?>
                  -<response>

                  -<system>
                  <version>1.0.2</version>
                  <time>1477665714</time>
                  </system>
                  </response>

                  Comment


                    #24
                    Thanks

                    Understood! Thanks!

                    Comment


                      #25
                      Hey,

                      Just got my Autelis for Hayward/Goldline and everything works great

                      Few questions:
                      1) can the device be named per Autelis app entry?
                      2) I have a salt cell can we get Salt Level?

                      Thanks, Steven G

                      Comment


                        #26
                        Originally posted by steveng View Post
                        Hey,

                        Just got my Autelis for Hayward/Goldline and everything works great

                        Few questions:
                        1) can the device be named per Autelis app entry?
                        2) I have a salt cell can we get Salt Level?

                        Thanks, Steven G
                        could you paste the following urls in a browser (replacing "your.ip.address" by the actual ip address of your Autelis controller) and post the xml results:
                        http://your.ip.address/names.xml
                        http://your.ip.address/chem.xml

                        thanks

                        Comment


                          #27
                          I get 404: File not found for both files

                          and I assume you were talking about Autelis IP not homeseer (but i tried it too)

                          Thanks
                          Steven G

                          Comment


                            #28
                            Originally posted by steveng View Post
                            I get 404: File not found for both files

                            and I assume you were talking about Autelis IP not homeseer (but i tried it too)

                            Thanks
                            Steven G
                            then I guess the answer to both your questions is no.
                            Anyway, I will confirm with Autelis directly.

                            Comment


                              #29
                              Dropdown or buttons for valves

                              Is there a way to create buttons or a dropdown for the valves. Currently, the only option is next. I tried editing the the status graphics of the valve device to add button for pool / spa / spillover, but no change. ??
                              Larry

                              Comment


                                #30
                                Originally posted by lpcalcaterra View Post
                                Is there a way to create buttons or a dropdown for the valves. Currently, the only option is next. I tried editing the the status graphics of the valve device to add button for pool / spa / spillover, but no change. ??
                                unfortunately the only available control is to cycle through the options. I guess it's the same thing in the Autelis app, right?

                                Comment

                                Working...
                                X