Help - Doesn't Work

[Andy]

I've read others posts, checked cabling & Caddx parameters. I don;t get any zone updates.

Here is the log:
7/5/2003 2:49:26 PM __NEW__
7/5/2003 2:49:26 PM hsCaddx Started on COM 1 DEBUG_LEVEL = 3
7/5/2003 2:49:26 PM send_panel(): ||022300254C||
7/5/2003 2:49:27 PM send_panel(): ||022301264D||
7/5/2003 2:49:27 PM send_panel(): ||022302274E||
7/5/2003 2:49:28 PM send_panel(): ||022303284F||
7/5/2003 2:49:29 PM send_panel(): ||0223042950||
7/5/2003 2:49:30 PM send_panel(): ||0223052A51||
7/5/2003 2:49:30 PM send_panel(): ||0223062B52||
7/5/2003 2:49:31 PM send_panel(): ||0223072C53||
7/5/2003 2:49:32 PM get_event(): $read_port = ||09860000000841FF04825FCC||
7/5/2003 2:49:32 PM partition_status(): OLE->set z3 status to OFF
7/5/2003 2:49:32 PM partition_status(): OLE->set z2 status to ON
7/5/2003 2:49:32 PM refresh_zone_status(): Total Groups of Zones: 1
7/5/2003 2:49:32 PM send_panel(): ||0225002750||
7/5/2003 2:49:33 PM get_event(): $read_port = ||09860000000841FF04825FCC||
7/5/2003 2:49:33 PM send_panel(): ||0226002852||
7/5/2003 2:49:33 PM get_event(): $read_port = ||09860000000841FF04825FCC||
7/5/2003 2:49:35 PM get_event(): $read_port = ||09860000000841FF04825FCC||
7/5/2003 2:49:37 PM get_event(): $read_port = ||09860000000841FF04825FCC||
7/5/2003 2:49:40 PM get_event(): $read_port = ||09860000000841FF04825FCC||
7/5/2003 2:49:42 PM get_event(): $read_port = ||09860000000841FF04825FCC||
7/5/2003 2:49:45 PM get_event(): $read_port = ||09860000000841FF04825FCC||
7/5/2003 2:49:47 PM get_event(): $read_port = ||09860000000841FF04825FCC||
7/5/2003 2:49:50 PM get_event(): $read_port = ||09860000000841FF04825FCC||
7/5/2003 2:49:52 PM get_event(): $read_port = ||09860000000841FF04825FCC||
7/5/2003 2:49:55 PM get_event(): $read_port = ||09860000000841FF04825FCC||
7/5/2003 2:49:56 PM send_panel(): ||03BE0101C34B||
7/5/2003 2:49:57 PM get_event(): $read_port = ||09860000000841FF04825FCC||
7/5/2003 2:50:00 PM get_event(): $read_port = ||09860000000841FF04825FCC||
7/5/2003 2:50:02 PM get_event(): $read_port = ||09860000000841FF04825FCC||


Any ideas?
Thanks,
Andy

[Nitrox]

The panel is sending System Status messages every second. Try turning them off and see if you get better results.

-Nitrox

[Andy]

Thanks for the reply. By turning offSystem status messages I assume 210 (NX-8e) segment #2 bit 1. Tried turning everything off in 210 except 6 & 7. This is what I'm getting now:

7/5/2003 4:21:55 PM __NEW__
7/5/2003 4:21:55 PM hsCaddx Started on COM 1 DEBUG_LEVEL = 3
7/5/2003 4:21:55 PM send_panel(): ||022300254C||
7/5/2003 4:21:56 PM send_panel(): ||022301264D||
7/5/2003 4:21:57 PM send_panel(): ||022302274E||
7/5/2003 4:21:58 PM send_panel(): ||022303284F||
7/5/2003 4:21:58 PM send_panel(): ||0223042950||
7/5/2003 4:21:59 PM send_panel(): ||0223052A51||
7/5/2003 4:22:00 PM send_panel(): ||0223062B52||
7/5/2003 4:22:01 PM send_panel(): ||0223072C53||
7/5/2003 4:22:01 PM get_event(): $read_port = ||002D000705101D000032ADFF||
7/5/2003 4:22:02 PM refresh_zone_status(): Total Groups of Zones: 1
7/5/2003 4:22:02 PM send_panel(): ||0225002750||
7/5/2003 4:22:02 PM get_event(): $read_port = ||002D000705101D000032ADFF||
7/5/2003 4:22:02 PM send_panel(): ||0226002852||
7/5/2003 4:22:02 PM get_event(): $read_port = ||002D000705101D000032ADFF||
7/5/2003 4:22:03 PM get_event(): $read_port = ||002D000705101D000032ADFF||
7/5/2003 4:22:05 PM get_event(): $read_port = ||002D000705101D000032ADFF||
7/5/2003 4:22:08 PM get_event(): $read_port = ||002D000705101D000032ADFF||
7/5/2003 4:22:11 PM get_event(): $read_port = ||002D000705101D000032ADFF||
7/5/2003 4:22:13 PM get_event(): $read_port = ||002D000705101D000032ADFF||
7/5/2003 4:22:15 PM get_event(): $read_port = ||002D000705101D000032ADFF||
7/5/2003 4:22:18 PM get_event(): $read_port = ||002D000705101D000032ADFF||
7/5/2003 4:22:18 PM send_panel(): ||03BE0101C34B||
7/5/2003 4:22:21 PM get_event(): $read_port = ||002D000705101D000032ADFF||
7/5/2003 4:22:23 PM get_event(): $read_port = ||002D000705101D000032ADFF||
7/5/2003 4:22:26 PM get_event(): $read_port = ||002D000705101D000032ADFF||
7/5/2003 4:22:28 PM get_event(): $read_port = ||002D000705101D000032ADFF||

Also, tried connecting using Hyperterminal and panel is sending these messages repeatedly. Changed 207 to serial printer mode and panel dumps status log.

Thanks again for the help,
Andy

[Nitrox]

Andy, could you verify that the panel is in ASCII mode and not BINARY?

'002D000705101D000032ADFF' doesn't appear to be a valid panel message.

-Nitrox

[acely]

I am having a similar problem, but my string is
0986000000004001048055A1
and if I connect thru hyperterm, it's the same. If I change output to binary, it becomes unreadable, so I am sure it's ascii.

I was running Homeseer 1.6.0, and received an error in the log "CommitDeviceStatus: Subscript out of range", I have since upgraded to Homeseer 1.6.119 and the log error has gone away, but there is still no activity or interaction.
I am running Win XP

Thanks in advance,
ace

[This message was edited by acely on Sun, 03 August 2003 at 07:36 PM.]