Spud,
Doing my migration over to HS3 and implementing your KMS plug-in. This is a spanking new clean setup.
I'm having issues installing it correctly:
a. I initialized KMS from the Plug-Ins page and it created a KMS device associated with HomeSeer PC instance. That device turns on/off as expected with the mouse keyboard strokes of the HomeSeer PC.
b. I installed the KMS per your instructions on another machine...Laptop. It does NOT create another device. And it now turns on/off the KMS device that was associated with the HomeSeer instance above along with the HomeSeer PC keyboard mouse interactions.
c. For every additional machine I install this happens where they all control the one device.
d. In the Plug-Ins when I mouse over 'KMS' it shows a 'Config' option for each machine but the config page is just the 'General Settings'
e. I create another KMS instance (the + on the Plug-Ins page) and label it to match the remote machine and no joy on creating another device.
f. I disable all instances of the KMS plug-ins...reboot HS and then restart the remote machines I get a "Loaded Remotely" in the plug-in plus the Remote Plug-Ins below light up. But again NO new devices are present and they all turn on/off the original device that was created.
What am I doing wrong?
Ken J.
HomeSeer Version: HS3 Pro Edition 3.0.0.208
Operating System: Microsoft Windows 7 Professional - Work Station
System Uptime: 0 Days 0 Hours 15 Minutes 30 Seconds
IP Address: 192.168.0.179
Number of Devices: 546
Number of Events: 81
Enabled Plug-Ins
3.0.0.29: ADIO-100
2.0.63.0: BLStat
2.0.17.0: BLUPS
3.0.0.75: HSTouch Server
3.0.5579.19855: UltraECM3
3.0.5584.29762: UltraGCIR3
3.0.5755.18523: UltraMon3
3.0.5723.28727: UltraWeatherWU3
3.0.1.25: Z-Wave
Doing my migration over to HS3 and implementing your KMS plug-in. This is a spanking new clean setup.
I'm having issues installing it correctly:
a. I initialized KMS from the Plug-Ins page and it created a KMS device associated with HomeSeer PC instance. That device turns on/off as expected with the mouse keyboard strokes of the HomeSeer PC.
b. I installed the KMS per your instructions on another machine...Laptop. It does NOT create another device. And it now turns on/off the KMS device that was associated with the HomeSeer instance above along with the HomeSeer PC keyboard mouse interactions.
c. For every additional machine I install this happens where they all control the one device.
d. In the Plug-Ins when I mouse over 'KMS' it shows a 'Config' option for each machine but the config page is just the 'General Settings'
e. I create another KMS instance (the + on the Plug-Ins page) and label it to match the remote machine and no joy on creating another device.
f. I disable all instances of the KMS plug-ins...reboot HS and then restart the remote machines I get a "Loaded Remotely" in the plug-in plus the Remote Plug-Ins below light up. But again NO new devices are present and they all turn on/off the original device that was created.
What am I doing wrong?
Ken J.
HomeSeer Version: HS3 Pro Edition 3.0.0.208
Operating System: Microsoft Windows 7 Professional - Work Station
System Uptime: 0 Days 0 Hours 15 Minutes 30 Seconds
IP Address: 192.168.0.179
Number of Devices: 546
Number of Events: 81
Enabled Plug-Ins
3.0.0.29: ADIO-100
2.0.63.0: BLStat
2.0.17.0: BLUPS
3.0.0.75: HSTouch Server
3.0.5579.19855: UltraECM3
3.0.5584.29762: UltraGCIR3
3.0.5755.18523: UltraMon3
3.0.5723.28727: UltraWeatherWU3
3.0.1.25: Z-Wave
Comment