Originally posted by sparkman
View Post
Announcement
Collapse
No announcement yet.
Qubino z-wave - Working!
Collapse
X
-
TomKassel
-
Originally posted by U5tabil View PostQubino with Zw+ does not work with HS only old regular Zw.
Steve
Comment
-
Well I tested several dimmers and switches and they add poorly. I did manage to add some on fresh systems but not existing. I also sent a dimmer module to Richard in HS to test. But we never manage to get them working properly. I now use Fibaro dimmer 2. And they too dim very good. Just like the old qubino. One of the reasons I earlier used qubino was the possibility to dim low. Which the Fibaro dimmer 1 did not manage.
Sent from my E6853 using TapatalkCertified installer for HomeSeer, Control4, KNX and Eaton/xComfort
Comment
-
getting inputs to work?
The older regular ZW Qubino dimmers has 3 inputs. 1 for the dimmer itself and also two other inputs. Have anyone got these to work? I have been trying now to get a signal from them but it seems they don't respond. And i can't see any parameters for me to change to get them working like with the fibaro dimmer 2's.Certified installer for HomeSeer, Control4, KNX and Eaton/xComfort
Comment
-
Originally posted by U5tabil View PostThe older regular ZW Qubino dimmers has 3 inputs. 1 for the dimmer itself and also two other inputs. Have anyone got these to work? I have been trying now to get a signal from them but it seems they don't respond. And i can't see any parameters for me to change to get them working like with the fibaro dimmer 2's.stefxx
Comment
-
Originally posted by stefxx View PostThe new Qubine Z-Wave plus dimmer also has three inputs. I was able to get I2 working by adding an association to Group 5. Never tested I3.Certified installer for HomeSeer, Control4, KNX and Eaton/xComfort
Comment
-
Yes, he does.
But perhaps the firmware version is more interesting to know... ?HSPro 3.0.0.458, Z-NET with Z-wave plugin 3.0.1.190, RFXCOM + 2x RFXtrx433E, HSTouch, Squeezebox plugin, iTach IP/WF2IR & GC-100-6 with UltraGCIR, BLDenon, NetcamStudio, Jon00s Webpage builder, Harmony Hub plugin, SCSIP (with FreePBX), Arduino plugin, IFTTT, Pushalot plugin, Device History plugin.
Running on Windows 10 (64) virtualized on ESXi (Fujitsu Primergy TX150 S8).
WinSeer (for Win10) - TextSeer - FitbitSeer - HSPI_MoskusSample
Are you Norwegian (or Scandinavian) and getting started with HomeSeer? Read the "HomeSeer School"!
Comment
-
But interesting that you got the Zw+ to work I had to send them all back cause neither me or Richard at HS managed to get it working. Msybe there is an updated version from them now, I have to check that out
Sent fra min E6853 via TapatalkCertified installer for HomeSeer, Control4, KNX and Eaton/xComfort
Comment
-
I just noticed I am unable to set an association with an endpoint to HomeSeer. When I try to do so HS3 reports success, but no association has been made. The strange thing is than when I rescan a device, is also tries to set an association with an endpoint (and fails). Now I am wondering if that might be (part of) the problem that instant status is not working correctly?
This is what the log is showing during a rescan:
feb-13 10:00:24 Z-Wave ZME_UZB1: Adding association for Z-Wave device Begane grond Keuken Goap Switch Binary Node 12 Root (Node 12, Group 2, Endpoint 2) to HomeSeer
feb-13 10:00:24 Z-Wave ZME_UZB1: Adding association for Z-Wave device Begane grond Keuken Goap Switch Binary Node 12 Root (Node 12, Group 1, Endpoint 1) to HomeSeer
When trying to do the association manually, this is the result:
Associate Begane grond Keuken Goap Switch Binary Node 12 Root
with HomeSeer at Endpoint 1
at group 1
Result: Association set successfully
But in both cases, no association has been setup...
On the other hand, I always assumed that having the association set to Group 1 (without endpoint) is sufficient for Z-Wave plus devices. But I am not sure if my assumption is correct.
Some help from the HomeSeer team would be great herestefxx
Comment
Comment