Announcement

Collapse
No announcement yet.

RFXCOM receiver & transmitter plug-in

Collapse
This topic is closed.
X
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

    #16
    RFXCOM plug-in version 14.0.0.56

    NEW OR CHANGED:
    Device options added for RFXCOM Devices.
    House Code redirect for X10 RF devices changed from A-P to A-Z.
    Device code offset added for X10 RF devices.
    Check on Unlock code done in the SetAlarmPanel function. (change your scripts if you use this function)
    Security sensor battery sensors added.


    CORRECTIONS:
    RTS10 device did not work when a device code > 9 was used.
    CM119 Total Power displayed value corrected.
    Sometimes the Daily Virtual Sensors are not reset at midnight.
    Linked sensor updates corrected.

    Comment


      #17
      RFXCOM plug-in version 14.0.0.60

      NEW OR CHANGED:
      -

      CORRECTIONS:
      Robocam/Ninja corrected
      Multiple sensor ID not automatically updated
      Dialy Virtual sensors have Reset button
      Unlock code cleared

      Comment


        #18
        RFXCOM plug-in version 14.0.0.62

        NEW OR CHANGED:
        -

        CORRECTIONS:
        - IMPORTANT: security sensor communication failures sometimes not detected!
        - Disable/enable buttons were not created if security sensor is set as not active.
        - Security remote device value is now always set and not only if active.

        Comment


          #19
          RFXCOM plug-in version 14.0.0.65

          NEW OR CHANGED:
          WA10A supported
          AC and HE EU can use house codes A to Z
          Clear input / security sensor heard lists at midnight.
          RFXMeter calibration value automatically added at overrun

          CORRECTIONS:
          BBQ sensor display values above 199 degrees corrected
          Solved: Error message when BBQ sensor started without BBQ sensor started.
          X10 House code redirection corrected for HC > P

          Comment


            #20
            RFXCOM plug-in version 14.0.0.67

            NEW OR CHANGED:
            Transmitter number displayed in packet retry

            CORRECTIONS:
            RFXMeter counter rollover corrected
            Output Device save optimized

            Comment


              #21
              RFXCOM plug-in version 14.0.0.71

              NEW OR CHANGED:
              ANSLUT device support added
              Hidden feature: Startup - Redir=Yes/No added so that the default HS config web pages are redirected yes or no

              CORRECTIONS:
              wind gust calculation for Virtual sensor corrected
              wind chill display in C or F depending on Use metric selection
              wind gust calculation for Virtual sensor corrected

              Comment


                #22
                RFXCOM plug-in version 14.0.0.75

                NEW OR CHANGED:
                Input Device: Device Status set to 3 if communication failure else Device Status is 2

                CORRECTIONS:
                CM119 address changed (Modify the CM119 sensor and assign the new address found)
                Barometer icon correct displayed when alarm/warning is set
                Disarm button did not operate if state was disarm
                Last edited by b_weijenberg; April 2, 2011, 04:16 AM.

                Comment


                  #23
                  RFXCOM plug-in version 14.0.0.80

                  NEW OR CHANGED:
                  selection for RFXLAN I/O added
                  Auto update of RFXMeter overrun configurable
                  Redirect configuration page configurable (no support if switched off)
                  Support for KD101 Chacon,Avidsen,NEXA smoke detector added (needs 11201 RFXLAN)
                  Reset button added on security remote

                  CORRECTIONS:
                  Motion sensor having status "communication failure" or "tamper" sets alarm panel not ready
                  Packets where sometimes not correctly transmitted

                  Comment


                    #24
                    RFXCOM plug-in version 14.0.0.83

                    NEW OR CHANGED:
                    transmitter buffer size increased from 10 to 20 commands
                    buttons added on top of some config pages

                    CORRECTIONS:
                    Midnight reset of virtual daily utility and rain sensors corrected.
                    wind chill calculation corrected
                    Output device selection corrected

                    Comment


                      #25
                      RFXCOM plug-in version 14.0.0.84

                      NEW OR CHANGED:
                      Flamingo HouseCode A-P with DeviceCode 1-16 can be used
                      AB400 series supported (see chapter 11.3.1 in the RFXCOM User guide.pdf)

                      CORRECTIONS:

                      Comment


                        #26
                        RFXCOM plug-in version 14.0.0.85

                        --------------------------------------------------------------------------------
                        NEW OR CHANGED:


                        CORRECTIONS:
                        unwanted clearing of the heard lists solved

                        Comment


                          #27
                          RFXCOM plug-in version 14.0.0.88

                          NEW OR CHANGED:
                          RFXCOM User Guide updated
                          Additional sanity check on some sensor packets

                          CORRECTIONS:
                          Dim level commands for AC and HE EU units corrected

                          Comment


                            #28
                            RFXCOM plug-in version 15.0.0.02

                            NEW OR CHANGED:
                            Support for RFXtrx315 Visonic added
                            Support for RFXtrx433 with LightwaveRF, Mertik Maxitrol, la Crosse and TFA added
                            COM port detection changed.

                            CORRECTIONS:
                            no

                            Comment


                              #29
                              RFXCOM plug-in version 15.0.0.04

                              NEW OR CHANGED:
                              Input sensor battery low reset is now done with Modify-Save of the battery sensor.
                              Input sensor battery low message only once displayed in the Input dev message panel.

                              CORRECTIONS:
                              Plug-in initialization problem solved when using AC devices with HC > P
                              RFXtrx - ARC chime corrected
                              Status of a receiver was set to off-line if an RFXtrx was configured.
                              ANSLUT transmit corrected
                              Rain sensor values for old receiver and RFXtrx are now the same.
                              CM119 corrected.

                              Comment


                                #30
                                RFXCOM plug-in version 15.0.0.05

                                NEW OR CHANGED:
                                Dim/Bright added for dimmer modules

                                CORRECTIONS:
                                LWRF remote ID corrected to enable unit numbers.

                                Comment

                                Working...
                                X