Announcement

Collapse
No announcement yet.

decimalSeparator - multi reports in syslog

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

    decimalSeparator - multi reports in syslog

    Hi all,

    my syslog is floaded with messages from the arduino plugin:
    Dec 12 11:33:06 RPi3-HS3 start_homeseer.sh[2547]: decimalSeparator = .

    these messages appear 3 to 5 times per second.
    If I disable the plugin then these mesages disappear, that why I think the Arduino plugin is the cause.

    Is there a way to stop this? Any help appriciated.

    Regards, Cor

    HomeSeer Version: HS3 Standard Edition 3.0.0.368
    Linux version: Linux RPi3-HS3 4.9.35-v7+ #1014 SMP Fri Jun 30 14:47:43 BST 2017 armv7l GNU/Linux System Uptime: 0 Days 0 Hours 22 Minutes 4 Seconds
    IP Address: 192.168.1.20
    Number of Devices: 416
    Number of Events: 185
    Available Threads: 398

    Enabled Plug-Ins
    1.0.0.142: Arduino Plugin
    3.0.0.5: CM15A
    0.0.0.19: DoorBird
    0.0.0.35: Pushover 3P
    3.0.5917.35093: UltraLog3
    3.0.1.165: Z-Wave

    #2
    Originally posted by Cor View Post
    Hi all,

    my syslog is floaded with messages from the arduino plugin:
    Dec 12 11:33:06 RPi3-HS3 start_homeseer.sh[2547]: decimalSeparator = .

    these messages appear 3 to 5 times per second.
    If I disable the plugin then these mesages disappear, that why I think the Arduino plugin is the cause.

    Is there a way to stop this? Any help appriciated.

    Regards, Cor

    HomeSeer Version: HS3 Standard Edition 3.0.0.368
    Linux version: Linux RPi3-HS3 4.9.35-v7+ #1014 SMP Fri Jun 30 14:47:43 BST 2017 armv7l GNU/Linux System Uptime: 0 Days 0 Hours 22 Minutes 4 Seconds
    IP Address: 192.168.1.20
    Number of Devices: 416
    Number of Events: 185
    Available Threads: 398

    Enabled Plug-Ins
    1.0.0.142: Arduino Plugin
    3.0.0.5: CM15A
    0.0.0.19: DoorBird
    0.0.0.35: Pushover 3P
    3.0.5917.35093: UltraLog3
    3.0.1.165: Z-Wave
    Cor,

    This is a log that is written to the Console which on windows shows up only if Developer Mode is enabled but I guess this is different on Linux. I will remove this in the next release. V1.0.0.144 which I hope to get out in the next week.

    Greig.
    Zwave = Z-Stick, 3xHSM100� 7xACT ZDM230, 1xEverspring SM103, 2xACT HomePro ZRP210.
    X10 = CM12U, 2xAM12, 1xAW10, 1 x TM13U, 1xMS13, 2xHR10, 2xSS13
    Other Hardware = ADI Ocelot + secu16, Global Cache GC100, RFXtrx433, 3 x Foscams.
    Plugings = RFXcom, ActiveBackup, Applied Digital Ocelot, BLDeviceMatrix, BLGarbage, BLLAN, Current Cost, Global Cache GC100,HSTouch Android, HSTouch Server, HSTouch Server Unlimited, NetCAM, PowerTrigger, SageWebcamXP, SqueezeBox, X10 CM11A/CM12U.
    Scripts =
    Various

    Comment


      #3
      Hi Greig.

      For your interest, developer mode was not enabled in my case.
      Thanks again for all the good work!

      Regards,
      Cor

      Comment


        #4
        Fixed in Beta V.146 available in the updater.

        Greig.
        Zwave = Z-Stick, 3xHSM100� 7xACT ZDM230, 1xEverspring SM103, 2xACT HomePro ZRP210.
        X10 = CM12U, 2xAM12, 1xAW10, 1 x TM13U, 1xMS13, 2xHR10, 2xSS13
        Other Hardware = ADI Ocelot + secu16, Global Cache GC100, RFXtrx433, 3 x Foscams.
        Plugings = RFXcom, ActiveBackup, Applied Digital Ocelot, BLDeviceMatrix, BLGarbage, BLLAN, Current Cost, Global Cache GC100,HSTouch Android, HSTouch Server, HSTouch Server Unlimited, NetCAM, PowerTrigger, SageWebcamXP, SqueezeBox, X10 CM11A/CM12U.
        Scripts =
        Various

        Comment


          #5
          Thanks Greig, it's working fine now.
          -- Cor --

          Comment

          Working...
          X