Originally posted by sirmeili
View Post
Announcement
Collapse
No announcement yet.
Aeon Labs Aeotec Z-Wave Multi-Sensor 6, Gen5
Collapse
X
-
Does anyone else have this? I can't set parameter 41. I have tried setting it, getting the value, setting it back to it's default, etc. I have removed and completely factory reset the sensor and when I try and get parameter "41", It shows "ERROR". I can't set it I can't even get it to show the default value (20). The other parameters seem to work fine (set and get). I think I saw that FW1.8 was out, so I may try and update to that and see if it fixes it.
Edit: No 1.8 that I can see, so I'm curious what the issue could be
Comment
-
Originally posted by sirmeili View PostDoes anyone else have this? I can't set parameter 41. I have tried setting it, getting the value, setting it back to it's default, etc. I have removed and completely factory reset the sensor and when I try and get parameter "41", It shows "ERROR". I can't set it I can't even get it to show the default value (20). The other parameters seem to work fine (set and get). I think I saw that FW1.8 was out, so I may try and update to that and see if it fixes it.
Edit: No 1.8 that I can see, so I'm curious what the issue could be
Maybe I just got a bum unit. I also emailed Aeotec's support. Though I may just get a replacement from Amazon.
Comment
-
Originally posted by sirmeili View PostDoes anyone else have this? I can't set parameter 41. I have tried setting it, getting the value, setting it back to it's default, etc. I have removed and completely factory reset the sensor and when I try and get parameter "41", It shows "ERROR". I can't set it I can't even get it to show the default value (20). The other parameters seem to work fine (set and get). I think I saw that FW1.8 was out, so I may try and update to that and see if it fixes it.
Edit: No 1.8 that I can see, so I'm curious what the issue could be
Has anyone successfully set parameter 41? I can't even get parameter 5 to work. I have 40 set to 0 (should ignore 41-43), but I still only get updates every hour. I don't get updates on motion like I think I should.
Maybe I'm misunderstanding parameter 5 though. I thought that sent the sensor data, but from what they say that's not what it does.
They said on battery it will update only every hour and not any faster. This sucks cause my Fibaro one updates on change for any of it's sensors. I was hoping this would be the same way. It's not really of use to me if I only get Humidity reports once an hour in a bathroom.
Comment
-
I am sooo disappointed now. I was hoping for real time updates of the sensor data (or close to it). Aeotec has confirmed that I can't really do that (at least on battery power). I can do it on USB power or by setting the wakeup period to less than an hour (they say you can do this to force hourly updates to be less than an hour).
I guess this is where the Fibaro multisensor is superior. It gives me updates as the data changes.
I was planning on doing USB power eventually anyways, so I guess I will have to run the USB cable and set the reporting to like once a minute. If I can get parameter 41 to work, then I will use that to limit network congestion. I was hoping to put these all over my house, but not sure I will now as some would have to be battery powered.
I hope the above helps someone who might be looking at this sensor.
Comment
-
doesn't generate uv device
just got it. went zwave 3.0.1.55 to get that to work. node information shows uv, but device not generated. called tech support at hs - 10 minutes of my life I'll never get back. "product does not support a uv device" despite what aeon says.. "can't help you open ticket." bugzilla ticket opened.
Any ideas?
Comment
-
Set Luminance?
I have installed 3.0.1.92 plugin and now get the child devices correctly.
I have also managed to get a reading of Luminance but it was 14% with a bright light shining on it, albeit not directly into the small hole. I get 0% when the standard light is turned on in the room where the sensor is located.
Is there a way to alter the calibration of the luminance?
EDIT - OK, found it!!
Comment
Comment