Any update on the issues with Homeseer and Aeon Labs ZW096 Smart Switch 6?
Announcement
Collapse
No announcement yet.
Aeotec Smart Switch 6 - parameters solved!
Collapse
X
-
Originally posted by lifespeed View PostAny update on the issues with Homeseer and Aeon Labs ZW096 Smart Switch 6?
Mode Parameter Value (Decimal) Value Size
Energy 81 0 Auto
Auto off 81 1 Auto
Night Light 81 2 Auto
For Night Light, you need to remember to turn the Multi-Level on (or Dim to preferred level) AND choose your colors and intensity (for Red, Green, and Blue). I set these through my Night Light event. For Example:
event: Set Table Lamp to Night Light modeManually triggered
Then Z-Wave Action - set parameter 81 / 2 / auto
Then Control DeviceTable Lamp - Color Blue - On
Table Lamp - Green - On
Table Lamp - Red - Off
Comment
-
I have one of these as well and they seem to report watts, amps, etc but then they will stop reporting any changes at all. I am using the latest ZWave plugin. What is the proper way to assign the groups for watts, amps, kwh, volts
I just want to use the energy monitoring feature of it.
Has anyone else seen this?
Comment
-
I have a couple of the Aeon Smart Switch 6 which I use for monitoring Watts consumed to determine if my TVs are turned on or off. They are configured to send a wattage report every 5 seconds to Group 1 which is HS3. The only time they stop reporting is when the Watts consumed is zero. Here are my root device settings for the Kitchen TV switch and the log that show the watts used reports:
Comment
-
They are shown in the embedded attachments, but here are the direct links:
http://imgur.com/t3J8AbS
http://imgur.com/bEL12tC
Comment
-
Originally posted by essjay View PostWhat do you guys set as the polling interval? I have it at 2s currently....
It depends on what you are doing with the information, but for most items I chose to report watts every minute, volts every 10 minutes and KWH every 6 hours. I don't bother with power. I have a couple of items that I use the watts consumed to trigger other events for entertainment devices (like turning subwoofers on when the receiver is powered) that I report watts every 30 seconds. For my satellite dish heater I only report watts every 5 minutes, since I am only charting the consumption and it is a steady state current when it is on.HS4 Pro, 4.2.19.16 Windows 10 pro, Supermicro LP Xeon
Comment
-
In the settings, Volts do not come up as an option to check the box (where you check the box for sending information to devices in group 1 etc). But if I set the polling interval then the volts & amps get updated in my devices list.
Tbh I’m still not entirely sure what the settings for sending information to devices in group one etc. Is that just essentially to set different reporting intervals for the V, W etc?
I only seem to have two options there - Meter (kWh) and Meter (W)
Comment
-
I'm at a loss as why you don't see Volts and Amps. I did not have to set any parameter to enable these. They showed up by default when the switch was included. Have you tried excluding the device from HS and including it again? Maybe something went wrong in the inclusion process.
Also, I am at HS3 3.0.0.368 with Z-Wave Plugin version 3.0.1.144. Are you on recent versions of HS3 and Z-Wave. Not sure you need to be at these versions for compatibility of the Aeon switch - but another troubleshooting step to consider.
Comment
-
i have the same problem , i resolved it by setting the polling for volt, Kwh and amperes
urrent Date/Time: 15/11/2017 21:01:39
HomeSeer Version: HS3 Pro Edition 3.0.0.372
Operating System: Microsoft Windows 10 Famille - Work Station
System Uptime: 0 Days 23 Hours 50 Minutes 19 Seconds
IP Address: 192.168.50.53
Number of Devices: 401
Number of Events: 142
Available Threads: 200
Enabled Plug-Ins
2.0.35.0: BLLAN
1.0.3.0: BLShutdown
2.0.10.0: BLUSBUIRT
4.8.6.0: BULLET
0.0.0.27: drhsIpPlugIn
3.0.0.64: mcsXap
3.0.0.14: NetCAM
3.0.1.109: PHLocation
30.0.0.36: RFXCOM
5.0.2.0: SCREPOSITORY
4.0.0.4: THERMOSTAT
3.0.0.44: X10
3.0.1.130: Z-Wave
Jean-Francois
Comment
Comment