Go Back   HomeSeer Message Board > HomeSeer Products & Services > HomeSeer Hardware > SmartStick+

SmartStick+ Discussions related to the HomeSeer SmartStick+ Z-Wave USB interface

Thread Tools Display Modes
Old July 16th, 2017, 11:21 PM
devoir devoir is offline
Seer Deluxe
Join Date: Dec 2014
Posts: 348
Aeon Labs MultiSensor Gen 1/2 Red Led ON

I have a Aeon Labs MultiSensor the red sensor light is staying on all the time unless i remove the battery. I can't seem to reset it or figure out how to do a factory reset.

This device is no longer seen by the Z-Wave stick. I have been trying to remove it from the group.

Any thought on why the red light is on 100% of the time???

Reply With Quote
Old July 17th, 2017, 12:38 AM
wadesready wadesready is online now
Seer Deluxe
Join Date: Mar 2017
Location: cabo rojo puerto rico
Posts: 238
I have a multisensor 6 that I run on usb with a red light on it all the time.... it is suppose to be green when it senses activity....I was spraying some ants one day right around it and after that the red light all the time..... still works though.
Reply With Quote
Old July 18th, 2017, 09:34 PM
devoir devoir is offline
Seer Deluxe
Join Date: Dec 2014
Posts: 348
Battery vs USB

I have several units some are on battery and some on USB . THose on USB the Red Light is always on.

THose on Battery only illuminate when motion is detected.....

So I can't figure out why the battery unit Red Light stays on 100% of the time...

Reply With Quote
Old July 19th, 2017, 12:18 AM
andyf andyf is offline
Seer Deluxe
Join Date: Apr 2017
Location: Houston, TX
Posts: 146
Have you waited longer than 10 minutes? The sensor will stay awake for 10 minutes after inserting the battery, unless you disable that feature.
Reply With Quote
Old July 20th, 2017, 07:36 PM
devoir devoir is offline
Seer Deluxe
Join Date: Dec 2014
Posts: 348
Red light on 24 hours later......

Motion is not triggering device...

Guess this means it's dead
Reply With Quote
Old August 15th, 2017, 06:53 AM
ShimmerNZ's Avatar
ShimmerNZ ShimmerNZ is offline
Seer Deluxe
Join Date: Jan 2013
Location: New Zealand
Posts: 167
Any luck fixing it? I have just had one exhibit the exact same symptoms. Red light on continuous even 24 hours on running on batteries. Just stopped working out of blue. New batteries made no difference.
Reply With Quote


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Aeon Labs Multisensor 6 sirexilon HomeSeer Hardware 28 April 3rd, 2018 11:14 PM
Aeon Labs Multisensor antoon HomeSeer Hardware 5 October 3rd, 2014 08:04 AM
Aeon Labs Z-Wave Multisensor freeon HomeSeer General Discussion Area 9 August 20th, 2014 02:31 PM
Aeon Labs MultiSensor Name HomeSeer Z-Wave Plug-in 78 September 12th, 2013 08:22 AM
Aeon Labs Z-Wave Multisensor Mrodseth HomeSeer Z-Wave Plug-in 1 December 31st, 2012 05:50 AM

All times are GMT -4. The time now is 06:33 AM.

Copyright HomeSeer Technologies, LLC