Announcement

Collapse
No announcement yet.

Can't seem to get UPB to work

Collapse
X
Collapse
 
  • Page of 1
  • Filter
  • Time
  • Show
Clear All
new posts
Previous template Next
    #1

    Can't seem to get UPB to work

    I ran the setup through UPStart, found the device, configured the device, tested comm, tested functionality. Exported as directed and still get the below error. I'm connecting to UPB Lamp Module...

    Any ideas?



    4/15/2007 10:43:03 PM : Initializing UPB PIM on USB port
    4/15/2007 10:43:03 PM : HID Device 1 Vendor ID 1118 Product ID: 157
    4/15/2007 10:43:03 PM : HID Device 3 Vendor ID 1118 Product ID: 157
    4/15/2007 10:43:03 PM : HID Device 4 Vendor ID 1118 Product ID: 157
    4/15/2007 10:43:03 PM : HID Device 5 Vendor ID 1193 Product ID: 4865
    4/15/2007 10:43:03 PM : HID Device 6 Vendor ID 1193 Product ID: 4865
    4/15/2007 10:43:03 PM : HID Device 7 Vendor ID 1193 Product ID: 4865
    4/15/2007 10:43:03 PM : HID Device 8 Vendor ID 1118 Product ID: 109
    4/15/2007 10:43:03 PM : HID Device 9 Vendor ID 1118 Product ID: 109
    4/15/2007 10:43:03 PM : HID Device 10 Vendor ID 1118 Product ID: 109
    4/15/2007 10:43:03 PM : HID Device 11 Vendor ID 1118 Product ID: 109
    4/15/2007 10:43:03 PM : PLC not found.
    4/15/2007 10:43:03 PM : ***:Error in InitIO: System.Exception: Can not find the UPB PIM. Please check your UPB configuration settings.
    at HSPI_UPB.HSPI.InitIO(Int64 Port)
    Tags: None
    #2
    What PIM are you using?

    Jon


    Originally posted by awizrd View Post
    I ran the setup through UPStart, found the device, configured the device, tested comm, tested functionality. Exported as directed and still get the below error. I'm connecting to UPB Lamp Module...

    Any ideas?



    4/15/2007 10:43:03 PM : Initializing UPB PIM on USB port
    4/15/2007 10:43:03 PM : HID Device 1 Vendor ID 1118 Product ID: 157
    4/15/2007 10:43:03 PM : HID Device 3 Vendor ID 1118 Product ID: 157
    4/15/2007 10:43:03 PM : HID Device 4 Vendor ID 1118 Product ID: 157
    4/15/2007 10:43:03 PM : HID Device 5 Vendor ID 1193 Product ID: 4865
    4/15/2007 10:43:03 PM : HID Device 6 Vendor ID 1193 Product ID: 4865
    4/15/2007 10:43:03 PM : HID Device 7 Vendor ID 1193 Product ID: 4865
    4/15/2007 10:43:03 PM : HID Device 8 Vendor ID 1118 Product ID: 109
    4/15/2007 10:43:03 PM : HID Device 9 Vendor ID 1118 Product ID: 109
    4/15/2007 10:43:03 PM : HID Device 10 Vendor ID 1118 Product ID: 109
    4/15/2007 10:43:03 PM : HID Device 11 Vendor ID 1118 Product ID: 109
    4/15/2007 10:43:03 PM : PLC not found.
    4/15/2007 10:43:03 PM : ***:Error in InitIO: System.Exception: Can not find the UPB PIM. Please check your UPB configuration settings.
    at HSPI_UPB.HSPI.InitIO(Int64 Port)
    Jon Ort
    JonOrt@The--Orts.com
    (Remove the dashes in the address, spam is getting out of hand)

    Comment

      #3
      I'm new to this so bare with me....I purchased the HAL Deluxe which came with Lamp Module and USB UPB (Module plugs into power outlet and then into computer via USB). The device worked fine with HAL setup, and the UPStart program had no problems finding and interfacing with it. At this point the HAL System is functioning as it should, on, off, dim etc. SO at least I know that the hardware is functioning...

      Does this answer your question?

      Comment

        #4
        There are several manufacturers of PIMs, so I was asking which one you have. You may have received one of the newer ones that has a unique USB identifier that is not yet supported. Also only one program can use the PIM at one time - just checking.

        Jon


        Originally posted by awizrd View Post
        I'm new to this so bare with me....I purchased the HAL Deluxe which came with Lamp Module and USB UPB (Module plugs into power outlet and then into computer via USB). The device worked fine with HAL setup, and the UPStart program had no problems finding and interfacing with it. At this point the HAL System is functioning as it should, on, off, dim etc. SO at least I know that the hardware is functioning...

        Does this answer your question?
        Jon Ort
        JonOrt@The--Orts.com
        (Remove the dashes in the address, spam is getting out of hand)

        Comment

          #5
          So if I'm understanding correctly, I can only use the PIM with HAL or HS at one time. Thankfully, this is how I'm configured so this shouldn't be an issue. You mentioned that there are multiple PIMs, can you tell me where I might purchase these, or is there still hope in getting mine up and running?

          Thanks for your time in case I didn't mention it earlier

          Comment

            #6
            We should start by figuring out what you have. Can you look at the label on the interface and tell me what it says?

            Jon


            Originally posted by awizrd View Post
            So if I'm understanding correctly, I can only use the PIM with HAL or HS at one time. Thankfully, this is how I'm configured so this shouldn't be an issue. You mentioned that there are multiple PIMs, can you tell me where I might purchase these, or is there still hope in getting mine up and running?

            Thanks for your time in case I didn't mention it earlier
            Jon Ort
            JonOrt@The--Orts.com
            (Remove the dashes in the address, spam is getting out of hand)

            Comment

              #7
              Computer Interface Module HAL-RCIUSB01 by Home Automated Living

              Comment

                #8
                Bueller....Anyone....Bueller.....

                Comment

                  #9
                  You can purchase a Simply Automated PIM from Home Controls in San Diego http://www.homecontrols.com/cgi-bin/...terface-Module

                  or Automated Outlet in Texas

                  http://www.automatedoutlet.com/produ...cat=145&page=1

                  Comment

                    #10
                    A stupid question....but...Are both of these models supported by HS? I think that was the issue with my HAL version. Documentation doesn't show that my model is supported

                    Comment

                      #11
                      The Simply automated PIM should work fine with HS. I am using a PIM from Powerline Control Systems and it works great with HS. I purchesed it direct from PCS http://www.pcslighting.com/ Their products are a little pricey but they cater to the professional installer. They are the creaters of the UPB technology.
                      Another site you might enjoy is Simply Automated http://simply-automated.com/ The guys at PCS and Simply Automated welcome calls with questions on UPB.

                      Dave

                      Comment

                      Previous template Next
                      Working...
                      X