Announcement

**bsobel** · May 8, 2018, 10:11 AM

I have not seen any reports of this before, albeit I have seen issues with a number of plugins starting with UW3 is on the system. I reported the issue to him, he blamed HS and didn't investigate. Any chance you could disable that for a few hours and check if this issues clears up during that time?

**monument** · May 8, 2018, 11:26 AM

sure, wilco. stay tuned.

**bsobel** · May 8, 2018, 11:30 AM

I noticed you have a few other plugins from the same author, I only have WU3, so (if possible) you may try the same test with the others as well (I realize this can be a pain, so no heroics, just trying to narrow down if there is indeed a common issue since I saw this as well)

**monument** · May 8, 2018, 12:05 PM

success! (at least initially) see attached log file snips (scenemasterX1 -X4)
i rebooted the PC and let it auto-start HS3 per usual. (X1)
You can see in X2 that Scenemaster fails, then tries again and fails, etc. That's the behavior I was seeing.
Then I killed UW3 (file X3), and when scenemaster restarted again (automatically) it worked fine. File X4 shows the completion.

Not my place to say anything about UW3 but i do think i'll run for a while without it. If that is the issue I hope it can get sorted -- all these PIs become important when you build interfaces and functions that use them.

Thanks a ton for the fast help. -mike

Attached Files

**monument** · May 8, 2018, 12:09 PM

sorry i'm not sure if the filenames are visible, but in my view X1 is top and X4 is bottom. just use the timestamps to sort them out....

**bsobel** · May 8, 2018, 07:15 PM

The UW3 author replied that he found an issue and you should upgrade to "UltraWeatherWU3 HSPI version 3.0.6702.34494." and see if that resolves it.

**Eman** · May 9, 2018, 02:50 AM

Hello,

Can you make a backup of your HomeSeer folded then upgrade to the latest version of HomeSeer =====> 3.0.0.435 ===> See if the problem persists.
I use the plugin with no issues!

Eman.

**Eman** · May 9, 2018, 02:58 AM

Originally posted by monument View Post

recently scenemaster is getting into a failure mode where auto-restarts don't fix it. Seems that when i manually disable and re-enable the PI from the PI-management page it works fine, for a while at least.
Now i'm also seeing the same failures on HS3 start-up.

I attached a couple snips from the HS log file showing the errors.
i'm running 1.2.2.0

Thanks for any help -- Scenemaster is pretty tightly stitched into my system design -- when it fails the house is messed up.
-mike

MESSAGE BOARD (copy/paste section below to message board posts)

Current Date/Time: 5/8/2018 9:54:50 AM
HomeSeer Version: HS3 Pro Edition 3.0.0.425
Operating System: Microsoft Windows 10 Pro - Work Station
System Uptime: 0 Days 0 Hours 25 Minutes 13 Seconds
IP Address: 192.168.1.64
Number of Devices: 1400
Number of Events: 224
Available Threads: 800
HSTouch Enabled: True
Event Threads: 0
Event Trigger Eval Queue: 0
Event Trigger Priority Eval Queue: 0
Device Exec Queue: 0
HSTouch Event Queue: 0
Email Send Queue: 0
Anti Virus Installed: Windows Defender

Enabled Plug-Ins
1.0.0.142: Arduino Plugin
2.0.5.0: BLTouchString
3.1.1.24385: Blue-Iris
0.0.0.26: drhsIpPlugIn
3.0.0.46: EasyTrigger
3.0.0.24: Ecobee
3.0.0.103: LutronCaseta
1.1.17344.312: MyQ
2.1.6.0: OpenSprinkler
1.0.0.7: Restart
1.2.2.0: SceneMaster
3.0.4.6: Tasker Plugin
3.0.6551.16959: UltraGCIR3
3.0.6554.33094: UltraMon3
3.0.6358.20184: UltraRussoundAudio3
3.0.6678.32863: UltraWeatherWU3
3.0.1.190: Z-Wave

@monument,

Can you please attend to a private message in your inbox at the top right corner of this page?

Eman.

Announcement

Scenemaster init failures

Scenemaster init failures

Comment

Comment

Comment

Comment

Comment

Comment

Comment

Comment