Announcement

Collapse
No announcement yet.

X10 issues

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

    #16
    Originally posted by Steve Q View Post
    I'm not sure I understand how you are using motion detection. Your event sets the motion sensor device to ON. If it is working properly it should change to ON independently. Do you have multiple "garage motion" devices?

    My x10 motion sensor devices change from off to on automatically. Your log should have lines something like: BLFR........CAPI control.........

    Steve Q


    Sent from my iPad using Tapatalk

    so here is the deal. Yes my garage motion does work.. works great with BLRF...

    HOWEVER there is one drawback. Years ago in HS2.5 I had it where you would open the door (ds10a) and event would say turn on the light. But I have times when the door is opened and NO ONE WALKS OUT THERE.... so motion is never tripped and light stays on all the time. Not a good solution.

    so I implemented the event to kick motion on.

    now I need to work on the motion even in the room so example...

    garage door from driveway is open already...
    you walk into garage
    motion is tripped and light turns on
    then while walking around... motion detected light stays on....

    in HS2 the way someone showed me how to do that was...

    create an event to turn off the garage light but it is a manual trigger

    then a second event that when motion is triggered it would...
    1. remove manual event run
    2. schedule manual event run again....

    think that was how it was...
    HW - i5 4570T @2.9ghz runs @11w | 8gb ram | 128gb ssd OS - Win10 x64

    HS - HS3 Pro Edition 3.0.0.435

    Plugins - BLRF 2.0.94.0 | Concord 4 3.1.13.10 | HSBuddy 3.9.605.5 | HSTouch Server 3.0.0.68 | RFXCOM 30.0.0.36 | X10 3.0.0.36 | Z-Wave 3.0.1.190

    Hardware - EdgePort/4 DB9 Serial | RFXCOM 433MHz USB Transceiver | Superbus 2000 for Concord 4 | TI103 X-10 Interface | WGL Designs W800 RF | Z-Net Z-Wave Interface

    Comment


      #17
      OK, a bit too complicated for me, but I get the idea. It will be difficult to troubleshoot. You might want to use a simpler setup to see how the motion sensor will work. My garage motion sensor has worked for the past few days. Today it's not working! I don't know why!

      Steve Q


      Sent from my iPad using Tapatalk
      HomeSeer Version: HS3 Pro Edition 3.0.0.368, Operating System: Microsoft Windows 10 - Home, Number of Devices: 373, Number of Events: 666, Enabled Plug-Ins
      2.0.83.0: BLRF, 2.0.10.0: BLUSBUIRT, 3.0.0.75: HSTouch Server, 3.0.0.58: mcsXap, 3.0.0.11: NetCAM, 3.0.0.36: X10, 3.0.1.25: Z-Wave,Alexa,HomeKit

      Comment


        #18
        Originally posted by Steve Q View Post
        OK, a bit too complicated for me, but I get the idea. It will be difficult to troubleshoot. You might want to use a simpler setup to see how the motion sensor will work. My garage motion sensor has worked for the past few days. Today it's not working! I don't know why!

        Steve Q


        Sent from my iPad using Tapatalk
        this is the same thing that happens to me.
        I got on a install rampage and got a mess done on a day. Busy the next few I went back to test some things and they werent working. Nothing changed.

        That is why it would be nice to have someone that owns the x10 plugin to see if it is that and how to debug...
        HW - i5 4570T @2.9ghz runs @11w | 8gb ram | 128gb ssd OS - Win10 x64

        HS - HS3 Pro Edition 3.0.0.435

        Plugins - BLRF 2.0.94.0 | Concord 4 3.1.13.10 | HSBuddy 3.9.605.5 | HSTouch Server 3.0.0.68 | RFXCOM 30.0.0.36 | X10 3.0.0.36 | Z-Wave 3.0.1.190

        Hardware - EdgePort/4 DB9 Serial | RFXCOM 433MHz USB Transceiver | Superbus 2000 for Concord 4 | TI103 X-10 Interface | WGL Designs W800 RF | Z-Net Z-Wave Interface

        Comment

        Working...
        X