Anybody have one of these http://store.homeseer.com/store/Aeon...-P1325C48.aspx Under device management the only thing that shows up is "Aeon Lab Battery Node" but under devices status I see: battery, motion, LUX, humidity and temperature. Shouldn't I see 5 devices for this node were I can adjust the settings for each.
Announcement
Collapse
No announcement yet.
Aeon Labs Z-Wave Multisensor
Collapse
X
-
On the Device Management page - are you sure you dont have a filter set or the "hide marked items" icon toggled (upper-right)?HS4Pro on a Raspberry Pi4
54 Z-Wave Nodes / 21 Zigbee Devices / 108 Events / 767 Devices
Plugins: Z-Wave / Zigbee Plus / EasyTrigger / AK Weather / OMNI
HSTouch Clients: 1 Android
-
Originally posted by freeon View PostBefore I added the devices I had the device management page filtered to all Z-wave but since these were diffrent types of Z-wave than I already had these devices type were not listed. Clicked show all and they appeared. Thanks
Sent from my Xoom using Tapatalk 4HS4Pro on a Raspberry Pi4
54 Z-Wave Nodes / 21 Zigbee Devices / 108 Events / 767 Devices
Plugins: Z-Wave / Zigbee Plus / EasyTrigger / AK Weather / OMNI
HSTouch Clients: 1 Android
Comment
-
Originally posted by rmasonjr View PostIt's the best out of the ones available from HST.
I even stuck one inside my refrigerator and freezer to see how closely they tracked the DS18B20 OneWire devices. Not only were they spot-on, but they performed fine for a week even at 0 degrees F. I since installed the Everspring devices in the Refrigerator, freezer and chest freezer, because of their direct temperature readout LCD on the device. I was hesitant to drill hoes in my under warranty refrigerator to install the OneWire devices.HS4 Pro, 4.2.19.16 Windows 10 pro, Supermicro LP Xeon
Comment
-
Originally posted by rprade View PostI even stuck one inside my refrigerator and freezer to see how closely they tracked the DS18B20 OneWire devices. Not only were they spot-on, but they performed fine for a week even at 0 degrees F. I since installed the Everspring devices in the Refrigerator, freezer and chest freezer, because of their direct temperature readout LCD on the device. I was hesitant to drill hoes in my under warranty refrigerator to install the OneWire devices.HS4Pro on a Raspberry Pi4
54 Z-Wave Nodes / 21 Zigbee Devices / 108 Events / 767 Devices
Plugins: Z-Wave / Zigbee Plus / EasyTrigger / AK Weather / OMNI
HSTouch Clients: 1 Android
Comment
-
Originally posted by rmasonjr View PostGlad to hear this. I have 2 Oregon sensors in my fridge/freezer now, but would like to replace them with Z-Wave.
Like I said, I also like the LCD display on the Eversprings and they are backlit when you press a button. They are also programmable for notification on preset temperature or humidity levels, but I handle that with events. I also like their mounting and the fact that they use AA instead of AAA batteries - might last longer.HS4 Pro, 4.2.19.16 Windows 10 pro, Supermicro LP Xeon
Comment
-
I bought a HSM100 to try out before I bought anymore. It was a bit of a pain to install it but once I did, it worked fine except the temperature reading was off by about 7 degrees. So I wrote a little script to write the compensated value into a virtual device. Just as I figure all that out, they went and discontinued that model. Nuts. How accurate is the temperature reading in the Aeon?
FYI - I use the HSM100 to determine a power failure. The motion sensor as read from Homeseer turns on when power is removed so I sense that state and if after 5 minutes it's still on, and if I get no status from 2 of my Foscams that are always powered on, I determine that it's not a glitch and a power outage has indeed occurred and I get sent an e-mail every 10 minutes until the UPS dies.
Does the motion sensor in the Aeon behave the same way?
Comment
Comment