I've been able to include/discover 5 Trane TCONT624 thermostats successfully into my HS3 ZEE S2, but the space temperature device on each one came in as an "Unknown Subtype" and reads a value of "0". All other data such as modes and setpoints came in just fine. I believe this is the same as the Nexia XL624 thermostat. Anyone have any ideas why the temperature doesn't seem to be compatible?
Announcement
Collapse
No announcement yet.
Trane TCONT624 T-Stat
Collapse
X
-
Originally posted by BillBeauvais View PostI've been able to include/discover 5 Trane TCONT624 thermostats successfully into my HS3 ZEE S2, but the space temperature device on each one came in as an "Unknown Subtype" and reads a value of "0". All other data such as modes and setpoints came in just fine. I believe this is the same as the Nexia XL624 thermostat. Anyone have any ideas why the temperature doesn't seem to be compatible?
It should say:
Thermostat API, Type: Thermostat Temperature, SubType: Temperature
If not, I'd rescan the device. Also, which version of Zwave is your 624 running?
Z
-
Originally posted by vasrc View PostWhen you look at the device info for Temperature in the Advanced tab, what does the device type internal say?
It should say:
Thermostat API, Type: Thermostat Temperature, SubType: Temperature
If not, I'd rescan the device. Also, which version of Zwave is your 624 running?
Z
The device type internal says:
Thermostat API, Type: Thermostat Temperature, SubType: Unknown Type
The ZEE is not currently online at the job site, as I am working on the project from off site. I should be able to get it on site next week and try a rescan.
As far as versions go, the z-wave PI nodes info provides the following:
Version: 3.52 (ZDK 4.54.2)
Firmware: 2.12
As well as:
Type: 0x5452
ID: 0x5439
And the CC (command class) for the child device for the temperature, it says:
CC: Sensor Multilevel Ver: 5
Bill
Comment
-
Not sure if this helps, but I have the XL624 which reports the firmware as 2.5 rather than 2.12 that yours reports.
The device reports for the Temperature
Thermostat API, Type: Thermostat Temperature, SubType: Temperature.
I'm not sure where you can get the firmware and it might even be impossible to get an update. The only problem I have with mine - and I actually bought two of them is that when it calls for heat and when the furnace is heating, the status for the Operating State is "unknown". I can still trigger events from this and all functionality works just fine. There is no problem when cooling.
I actually contacted Trane and was told the firmware is not publically available. If anyone else has any luck in getting fw updates, I'd be interested.
From aside note, I tried to create an event which replaces the "unknown" string as "Heating", but for some reason it doesn't display... might be a plugin issue.
RobertHS3PRO 3.0.0.500 as a Fire Daemon service, Windows 2016 Server Std Intel Core i5 PC HTPC Slim SFF 4GB, 120GB SSD drive, WLG800, RFXCom, TI103,NetCam, UltraNetcam3, BLBackup, CurrentCost 3P Rain8Net, MCsSprinker, HSTouch, Ademco Security plugin/AD2USB, JowiHue, various Oregon Scientific temp/humidity sensors, Z-Net, Zsmoke, Aeron Labs micro switches, Amazon Echo Dots, WS+, WD+ ... on and on.
Comment
-
Originally posted by BillBeauvais View PostHi Z
The device type internal says:
Thermostat API, Type: Thermostat Temperature, SubType: Unknown Type
The ZEE is not currently online at the job site, as I am working on the project from off site. I should be able to get it on site next week and try a rescan.
As far as versions go, the z-wave PI nodes info provides the following:
Version: 3.52 (ZDK 4.54.2)
Firmware: 2.12
As well as:
Type: 0x5452
ID: 0x5439
And the CC (command class) for the child device for the temperature, it says:
CC: Sensor Multilevel Ver: 5
Bill
Z
Comment
-
Originally posted by langenet View PostNot sure if this helps, but I have the XL624 which reports the firmware as 2.5 rather than 2.12 that yours reports.
The device reports for the Temperature
Thermostat API, Type: Thermostat Temperature, SubType: Temperature.
I'm not sure where you can get the firmware and it might even be impossible to get an update. The only problem I have with mine - and I actually bought two of them is that when it calls for heat and when the furnace is heating, the status for the Operating State is "unknown". I can still trigger events from this and all functionality works just fine. There is no problem when cooling.
I actually contacted Trane and was told the firmware is not publically available. If anyone else has any luck in getting fw updates, I'd be interested.
From aside note, I tried to create an event which replaces the "unknown" string as "Heating", but for some reason it doesn't display... might be a plugin issue.
Robert
2.5 (actually 2.05) is before 2.12, so he has the latest firmware. I have both .08 and .12 and I can't see any difference. The big issue I found (not a problem where he is in AZ, but you probably see it), is if you're running a heat pump, the defaults to kick in the heat strips is hard coded to 3 degrees delta and 3 mins.. AND it won't kick off the strips until you reach setpoint. Big power waster, especially in the AM when I start to warm up the house after letting it cool down in the evening..
Z
Comment
-
Right... Didn't know it was 2.05 since it reports Current Firmware: Manufacturer = Trane Corp Version: 2.5. Would you mind sharing the .12 FW or provide a link to where I can get it?
RobertHS3PRO 3.0.0.500 as a Fire Daemon service, Windows 2016 Server Std Intel Core i5 PC HTPC Slim SFF 4GB, 120GB SSD drive, WLG800, RFXCom, TI103,NetCam, UltraNetcam3, BLBackup, CurrentCost 3P Rain8Net, MCsSprinker, HSTouch, Ademco Security plugin/AD2USB, JowiHue, various Oregon Scientific temp/humidity sensors, Z-Net, Zsmoke, Aeron Labs micro switches, Amazon Echo Dots, WS+, WD+ ... on and on.
Comment
-
Originally posted by langenet View PostRight... Didn't know it was 2.05 since it reports Current Firmware: Manufacturer = Trane Corp Version: 2.5. Would you mind sharing the .12 FW or provide a link to where I can get it?
Robert
I've called Trane, the local distributor, Dist Tech specialist and no one is interested in providing it. I've got a trouble ticket with Trane looking at the premature Stage 2 issue, so I'll ask again. If I get it I'll LYK. Looks like HS provides a way to update the 624.
I just bought an 824 just for grins to muck with to see if I can bypass the internal bridge to Nexia and get it to connect to HS3.
Z
Comment
-
Originally posted by vasrc View PostA rescan should fix it I would think. Once the Subtype is correct, it should populate itself with the temp (usually takes a couple of minutes to be polled)
Z
Z-Wave Warning: Z-Wave Multilevel Sensor device xxx is missing Sensor Type information - cannot update sensor status.
Z-Wave Error: (2) Sensor Multilevel Report for type Air_Temperature received, but the corresponding device Node ID cannot be found. (2) Node/Instance=6/-1
Bill
Comment
-
Originally posted by BillBeauvais View PostWell, I was finally able to get the system installed at the site and perform a rescan of all the stats. Unfortunately, the rescan didn't resolve the problem. Looking at the Log, I see 2 related messages like the ones below.
Z-Wave Warning: Z-Wave Multilevel Sensor device xxx is missing Sensor Type information - cannot update sensor status.
Z-Wave Error: (2) Sensor Multilevel Report for type Air_Temperature received, but the corresponding device Node ID cannot be found. (2) Node/Instance=6/-1
Bill
Z
Comment
-
Originally posted by BillBeauvais View PostThe attached screenshot is the ZWave Node info for one of the stats.
Bill
Screen shot below.
Which vers of Z-wave plugin are you using?
Z
Comment
-
External Temperature?
Originally posted by Vyza View PostI've just added the Trane XL624 Thermostat to my system and wanted to know what the "General Purpose" child device is used for.
Does anyone know if it can report the outside temperature?
Also, I've noticed the "invalid value" on the operating state in the z-wave log entry. This occurs when the dual fuel option is engaged. When the secondary heat source is in use this is when the invalid value shows up. The device status in HS3 shows as unknown. Is this a change for the z-wave plugin? I am currently using version 3.0.1.162.
Dave
- Likes 1
Comment
Comment