GE Concord 4 - anyone set theirs up yet?

[TeleFragger]

Ok so I know a few were looking at this unit.. well I bought it and not sure how to configure the x10 side (since i got the x10 transformer pending the alarm plugin)

Ok so Im starting to get my concord 4 installed..
3 doors
9 windows
2 basement bars
2 glassbreaks
1 keyfob
are in... next is my smokes and water detector..

anyway... I bought the x10 transformer just so i can have a few virtual devices....

now I went into the alarm setup and went to lighting control.
I have it set to P as A was default

but in my homeseer logs it picks up more than that.... homeseer is picking up that the alarm is doing the following:

7/17/2008 11:26:14 PM X10 Received B1 (?) B Off
7/17/2008 11:26:16 PM X10 Received C1 (?) C Off
7/17/2008 11:26:18 PM X10 Received D1 (?) D Off
7/17/2008 11:26:20 PM X10 Received E1 (?) E Off
7/17/2008 11:26:22 PM X10 Received B1 (?) B Off
7/17/2008 11:26:25 PM X10 Received C1 (?) C Off
7/17/2008 11:26:27 PM X10 Received D1 (?) D Off
7/17/2008 11:26:29 PM X10 Received E1 (?) E Off
7/17/2008 11:26:32 PM X10 Received B1 (?) B On
7/17/2008 11:26:34 PM X10 Received G1 (?) G Off


this is before I set the house code in the alarm to P..
now that I have done that I get
7/17/2008 11:35:25 PM X10 Received P1 (?) P On
7/17/2008 11:35:28 PM X10 Received P2 (?) P On
7/17/2008 11:35:30 PM X10 Received P2 (?) P Off
7/17/2008 11:35:32 PM X10 Received P2 (?) P On
7/17/2008 11:35:34 PM X10 Received P2 (?) P Off
7/17/2008 11:35:37 PM X10 Received P2 (?) P On
7/17/2008 11:35:39 PM X10 Received P2 (?) P Off
7/17/2008 11:39:51 PM X10 Received C1 (?) C Off
7/17/2008 11:39:54 PM X10 Received D1 (?) D Off
7/17/2008 11:39:56 PM X10 Received E1 (?) E Off
7/17/2008 11:39:59 PM X10 Received F1 (?) F Off
7/17/2008 11:40:01 PM X10 Received C1 (?) C Off
7/17/2008 11:40:03 PM X10 Received D1 (?) D Off
7/17/2008 11:40:05 PM X10 Received E1 (?) E Off
7/17/2008 11:40:08 PM X10 Received F1 (?) F Off
7/17/2008 11:40:10 PM X10 Received G1 (?) G Off
7/17/2008 11:40:36 PM X10 Received P1 (?) P Off
7/17/2008 11:46:33 PM X10 Received J3 (?) J Off

so it seems P too affect.. however... why all the rest???
I dont use 1 for anything due to stuff like this.... my motion sensors when the batteries die default back to A1 so I have learned never use 1.... but I have...C for cralw, G for garage and a few of the others are used too..... like J3...

I am not sure how to set each one or at lease to get rid of all the housecodes that it is transmitting except for P

any ideas???

im wondering if P is now set for the lighting control as you see at the top.. on and offs.. for say alarm tripped...

wonder where you set for say a door is opened.... maybe that is what is sending the other housecodes????

[TeleFragger]

well I got the rest done... well almost.. just the water sensor.. cant seem to get it to work right...

partition 1 - group 38 (in book says water sensor) and it programs.
but when I try and arm the system it says - Sensor 18 Open..
so then I hit the program button and the alarm goes off so it is programmed in and working... but wont let me arm the system..... hmmm gotta figure that out..


added 2 smokes to finish up the hardware..

and now time to read on as I have to figure out how to set the x10 stuff...
setting off the alarm gives me
7/18/2008 8:09:26 PM X10 Received P2 (?) P Off
7/18/2008 8:09:28 PM X10 Received P2 (?) P On
7/18/2008 8:16:29 PM X10 Received P1 (?) P Off
7/18/2008 8:16:31 PM X10 Received C1 (?) C Off
7/18/2008 8:16:33 PM X10 Received D1 (?) D Off
7/18/2008 8:16:35 PM X10 Received E1 (?) E Off
7/18/2008 8:16:38 PM X10 Received P1 (?) P Off
7/18/2008 8:16:40 PM X10 Received C1 (?) C Off
7/18/2008 8:16:42 PM X10 Received D1 (?) D Off
7/18/2008 8:16:44 PM X10 Received E1 (?) E Off
7/18/2008 8:16:47 PM X10 Received F1 (?) F Off
7/18/2008 8:16:49 PM X10 Received G1 (?) G Off


so gotta clean that up a bit..


also piperpilot is working on getting some type of beta out to us.... cant wait..!!!!!