Announcement

Collapse
No announcement yet.

Aeon ZW096-A02 Smart Switch 6

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

    Aeon ZW096-A02 Smart Switch 6

    I picked up a couple of these smart plugs at a pretty good price. It seemed to include Ok, but none of the wattage information is being transmitted.

    I think maybe because there are no values set to the groups??
    Attached Files
    RJ_Make On YouTube

    #2
    I don't have this exact one, but they all seem the same. Under group 1 you should have Meter (kWh) Meter (W) Sensor (W) - Check boxes with Meter and Sensor checked.

    You may need to delete device and add it again so it shows up. One of my other Aeon Energy devices needed a firmware upgrade. First see if it needs firmware upgrade, then delete/add.
    Tom
    baby steps...starting again with HS3
    HS3Pro: Z-NET & 80 Z wave Devices,
    HSTouch: 4 Joggler (Android Kitkat), 2 iPhone, 3 iPads
    Whole House Audio: 5 SqueezePlay Jogglers w Bose Speakers
    In The Works: 10 Cameras Geovision, new Adecmo/Envisalink Alarm, Arduinos
    System: XP on Fanless Mini-ITX w/ SSD

    Comment


      #3
      If you can post a screenshot with the node info for this, that might help. Firmware is not always the problem but with Aeon stuff, it often is.
      💁‍♂️ Support & Customer Service 🙋‍♂️ Sales Questions 🛒 Shop HomeSeer Products

      Comment


        #4
        Originally posted by TomTom View Post
        I don't have this exact one, but they all seem the same. Under group 1 you should have Meter (kWh) Meter (W) Sensor (W) - Check boxes with Meter and Sensor checked.

        You may need to delete device and add it again so it shows up. One of my other Aeon Energy devices needed a firmware upgrade. First see if it needs firmware upgrade, then delete/add.
        I've already tried that, twice. Still no joy..
        RJ_Make On YouTube

        Comment


          #5
          Originally posted by macromark View Post
          If you can post a screenshot with the node info for this, that might help. Firmware is not always the problem but with Aeon stuff, it often is.
          Thanks. Will do.
          RJ_Make On YouTube

          Comment


            #6
            Here are the 2 I've added, I have 1 more I didn't bother to add at this point..
            Attached Files
            RJ_Make On YouTube

            Comment


              #7
              Soooo, Is there a way to get this working in HS?
              RJ_Make On YouTube

              Comment


                #8
                You can manually set the z-wave parameters to get the reporting the way you want it. See this thread for similar issues with the ZW078. I was finally able to get them working properly with the info Aeotec provided to me and setting the parameters manually.

                Cheers
                Al
                HS 4.2.8.0: 2134 Devices 1252 Events
                Z-Wave 3.0.10.0: 133 Nodes on one Z-Net

                Comment


                  #9
                  Thank you VERY much Al,

                  I set group 101 to 15 and all is working. I also change group 1 from 3 to 30 sec to keep the network from getting overloaded.
                  RJ_Make On YouTube

                  Comment


                    #10
                    Originally posted by ServiceXp View Post
                    Thank you VERY much Al,

                    I set group 101 to 15 and all is working. I also change group 1 from 3 to 30 sec to keep the network from getting overloaded.

                    You're welcome. Glad to help.

                    Cheers
                    Al
                    HS 4.2.8.0: 2134 Devices 1252 Events
                    Z-Wave 3.0.10.0: 133 Nodes on one Z-Net

                    Comment


                      #11
                      Here is the engineering information.
                      Attached Files
                      RJ_Make On YouTube

                      Comment

                      Working...
                      X